• ServiceYouTube
• Title🔥👉🏻 How to Make an RGB backlit LED Sign for Wall Decoration for a Studio or Office
• Duration7:44
• UploaderU Do It
• Views206,825
• DescriptionIn this video I show you how to make an RGB Backlit LED Sign. This is how to build a CNC Sign. Building a DIY CNC Sign using Hitlights RGB 16' LED light strip 🔴 http://amzn.to/2oOiuUU
  
  ⏬ Here are the products U Do It uses in making videos ⏬
  
  I enjoy fusing engineering with art to create #EngineeredArt. This video demonstrates how to build a backlit LED sign. The design is from the All Out Baseball team's logo and will be auctioned off to raise money for the team. The building process took approximately 16 hours to complete. The longest part was gluing on the LED strips and soldering them together.
  
  If you see YouTuber's studios they all have some form of backlighting. This would cast the perfect glow of color on a dimly lit wall with a Philip DeFranco style.
  
  The following steps were taken to complete the sign.
  1) Prep and tool logo cutout file for CNC
  2) Cutout logo on CNC out of 1/4" MDF and back
  3) Sand logo
  4) Trace cutout on back
  5) Place cutout pieces in center of cutout tracing
  6) trace the cutouts
  7) glue cutouts in place on back of board
  8) cut standoffs and position
  9) glue standoffs in place with cyanoacrylate glue
  10) paint back and cutout sides with primer
  11) paint pack and cutout with desired colors
  12) size LED strips and cut to length to be glued to back side of cutout
  13) position LED strips and glue in place
  14) strip and solder 4 wire to join the chains
  15) test the lights in Red, then Green, then Blue to ensure all wiring
  is perfect
  16) Do not glue the solder joints yet
  17) Complete all soldering and test
  18) glue all solder joints
  19) position cutout over back and trace standoff locations lightly with pencil
  20) mark center of each traced area on back
  21) drill a hole that matches the screw diameter in each marked area
  22) put the cutout on its front side down
  23) position the back oriented properly over the cutout
  24) with a center marker or a drill bit (by hand) mark the center point of the hole into the standoffs
  25) with a drill and a drill bit that is smaller than the screw drill to the depth of the screw
  26) countersink the holes in the back with a larger drill bit or a countersink bit
  27) Install the screws in each standoff
  28) mount a picture hanging kit in the back in the area of the center of gravity
  29) hang on a wall
  30) plug in and turn on the remote
  
  This is perfect for a youtube studio, live streaming, photo opportunities, selfies or just pure awesomeness.
  
  Please share this video and tag #udoit, #udoit2 and #EngineeredArt
  
  Materials Used Total $87:
  - 1/4" 2' x 4' MDF board $7
  - 200 grit 3M Sandpaper http://amzn.to/2nORBm6
  - White, Orange and Blue acrylic paints $5
  - Cyanoacrylate glue http://amzn.to/2nxGXO8
  - Hitlights RGB 16' LED light strip http://amzn.to/2oOiuUU
  - Dowel for standoffs $3
  - Behr Primer Paint $10.67
  - Wire http://amzn.to/2oOhWP6
  - Enpoint 1/8" single flute end mill http://amzn.to/2nLQvpC
  - Wood screws $1
  - E6000 Glue http://amzn.to/2oOiCUE
  - Small nuts and bolts for picture hanger $2
  
  Tools Used:
  - Homebuilt CNC
  - Drill http://amzn.to/2oykv8l
  - Drill bits http://amzn.to/2nxkil8
  - Air brush http://amzn.to/2nxyM4v
  - Compressor
  - Hobby pneumatic spray gun http://amzn.to/2oypnu9
  - Acrylic paint brushes http://amzn.to/2nLZiYH
  - Vaccuum
  - Dust brush
  - Miter Saw http://amzn.to/2nOJshs
  - Wood clamps http://amzn.to/2o09C1m
  - Digital Calipers http://amzn.to/2nxzZJ9
  
  “As an Amazon Associate I earn from qualifying purchases.”
  
  Please subscribe and be sure to set the notification on the channel so you are notified when it is available.
  
  This is for a fundraiser to help raise money for the team's expenses throughout the year. It will be auctioned off at the next event, which is February 4th, 2017.
  
  Music by:
  Julian Avila
  https://soundcloud.com/julian_avila
  
  All Out Baseball
  Twitter: @AllOutBaseball
  Instagram: @AllOutBaseball
  Tags: #AllOutBaseball #AOBaseball , How to Cutout a Logo

Download Links for
https://www.youtube.com/watch?v=7hMtsDaBHkA